TeamSwift

Ideally you'll want to have them ground (like a stock rebuild) , but they will work on a stock seat.

_________________
Contact 3tech: [email protected]

I want a rebuild kit for 99 for the g10 . Tell how you want to do this?

Man you guys are tempting me soooo........I think i wanna try those valves. I have a head waiting for some new oversized valves.

Im gonna talk to my builder and get back to you.

Are they stainless steel ???

_________________
http://www.facebook.com/profile.php?id=551883908

I think that the SS in his thread topic means "Stainless Steel" as opposed to the usual "Suzuki Swift" unless I'm mistaken.

_________________
~the other Ralph~
Certified Suzuki Owner:
MKIII Swift GTi - The Green Destiny!
2010 Suzuki Jimny - The DD Workhorse!

Email me at [email protected]

_________________
Contact 3tech: [email protected]

Got my set of SS valves from Mike.....pure sex! Here they are, just offered up to my cyl. head that I'm still working on:
gallery/image_page.php?album_id=1060&image_id=20222

_________________
~the other Ralph~
Certified Suzuki Owner:
MKIII Swift GTi - The Green Destiny!
2010 Suzuki Jimny - The DD Workhorse!

Now these are nice you produce some nice stuff, I got cam recently of piper woulda emailed you tho I was in a hurry , ill have a word with me building through week see if I can use these vales, you do anything in the line of springs ?

_________________
Flat To The Mat

Do you have the SS valves for the early (85-88) G10's? Time to rebuild my head.

Thanks

Sorry, I do not.

_________________
Contact 3tech: [email protected]

as asked previously....any valves for the sohc 16v heads?

oh yeah....10 month bump

_________________
98 swift 1.6 16v swap
03 cobra bolt ons
97 3000gt vr4 e85, high comp, bolt ons
too many others to list

I think I do have stock on both intake and exhaust

_________________
Contact 3tech: [email protected]

thanks for the response. i was hoping for oversize.

_________________
98 swift 1.6 16v swap
03 cobra bolt ons
97 3000gt vr4 e85, high comp, bolt ons
too many others to list

Good luck. Just finding stock ones is hard. Nobody makes oversize for this motor. The valve sizes are already good, though. Bigger than the GT, if I recall

_________________
Contact 3tech: [email protected]

So who has valve springs for a 16 valve heads? I would not want to upgrade the valves unless I could get new valve springs too.
The valve guides will also get replaced. Do you sell a kit that has valves, guides, and springs?

_________________
Fainya
97 Geo Metro LSI,1.3L-GT-DOHC-16v,4.10 5-speed,A/C,170,000,suspension lowered 1",4 wheel disk brakes,15"alloy wheels with 185/50-15 Toyo's,GT bucket seats,analog oil pressure gauge,cruise control, new paint job. 40 mpg at 65 mph.
Good, fast, cheap. You only get two.

At this point, all I have is guides. I used to sell those valves, but demand was so low I stopped stocking them. Stock, original springs are probably fine for anything other than sustained high RPM use.

_________________
Contact 3tech: [email protected]

Is there a good source for valve springs?
I would not want to put those new valves on old springs.

_________________
Fainya
97 Geo Metro LSI,1.3L-GT-DOHC-16v,4.10 5-speed,A/C,170,000,suspension lowered 1",4 wheel disk brakes,15"alloy wheels with 185/50-15 Toyo's,GT bucket seats,analog oil pressure gauge,cruise control, new paint job. 40 mpg at 65 mph.
Good, fast, cheap. You only get two.

No. Dealer only, but the stock springs are quite good.

_________________
Contact 3tech: [email protected]

I now have stock again on swirl polished 1 pc SS valves for G13 DOHC and G10 89+

G10's I have a few years stock, I essentially bought out the supplier

G13 stock is limited.

Valves are standard size.

Lot's of stock on the plain SS and non SS valves for G10

_________________
Contact 3tech: [email protected]